NEC Enterprise Series
®
®
MultiSync
E Series
User’s Manual
User’s Manual
Contents
Quick Start
Controls
1
2-3
4-5
Recommended Use 6-7
Specifications
Features
Troubleshooting
References
8-9
10
11
12
13
Limited Warranty
78131861
1
5/21/98, 2:22 PM
®
Contents
Your new NEC Technologies MultiSync® E Series monitor box*
should contain the following:
• MultiSync E Series Monitor with tilt/swivel base
MultiSync E500™, JC-1575VMA
MultiSync E700™, JC-1746UMA
• Power Cord
• Captive Signal Cable
• User’s Manual
• Registration Card
Power Cord
Captive Signal Cable
NEC
Enter
pr
NEC MultiSync Monitors
THAK YOU FOR
CHOOSIG AN NEC
MultiSync
ise
S
er
i
es
TION
MultiSync
To help us in our continuing e©ffMortsOtoNITOR
better serve and support you, and to bring
you new and innovative products, please
take a few moments to register your new
NEC MultiSync monitor.
— Important —
E
Series
User’s Manual
®
By returning this card, we confirm your
date of purchase and records the model
and serial numbers. This facilitates our
ability to process warranty claims,
especially if your original proof of
purchase is lost.
Thank you for your time and for choosing
an NEC MultiSync monitor.
PRODUCT REGISTRA
SEE, HEAR AND FEEL THE DIFFERENCE.
™
User’s Manual
Registration Card
* Remember to save your original box
and packing material to transport
or ship the monitor.
Note: You can now register your
product on the Internet at
1
78131861
3
5/21/98, 2:22 PM
Quick Start
To attach the MultiSync® E Series monitor to your system, follow
these instructions:
1. Turn off the power to your computer.
2. If necessary, install the display card into your system. For more information,
refer to the display card manual.
3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the
connector of the display card in your system (Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync E Series Macintosh cable adapter (not
included) to the monitor connector on the Macintosh (Figure B.1). Attach the
15-pin mini D-SUB end of the captive signal cable to the Macintosh cable
adapter on the computer (Figure B.1). Tighten all screws.
NOTE: To obtain the MultiSync E Series cable adapter, call
NEC Technologies at (800) 820-1230.
4. Connect one end of the power cord to the MultiSync E Series monitor and the
other end to the power outlet (Figure C.1).
5. Turn on the monitor (Figure D.1) and the computer.
NOTE: If you have any problems, please refer to the Troubleshooting section of
this User’s Manual.
Captive Signal Cable
15-pin mini D-SUB
Figure A.1
2
78131861
4
5/21/98, 2:22 PM
Quick Start
Captive Signal
Cable
Mac Adapter
(Not included)
15-pin mini D-SUB
Computer
Figure B.1
Power Outlet
Power
Cord
Figure C.1
MultiSync E500
EXIT
PROCEED RESET
CONTROL
Figure D.1
3
78131861
5
5/21/98, 2:22 PM
Controls
OSM™ (On-Screen Manager) control buttons on the front of the monitor function
as follows:
EXIT
Exits the OSM controls.
CONTROL ᮤ / ᮣ Moves the highlighted area left/right to select one of the controls.
CONTROL +/–
Moves the bar in the + or – direction to increase or decrease
the adjustment.
PROCEED
RESET
Enters OSM menu and selects icons at the top of the menu.
Resets the highlighted control to the factory setting.
Brightness/Contrast Controls
Adjusts the overall image and background screen brightness.
Adjusts the image brightness in relation to the background.
Size and Position Controls
Moves the image horizontally (left or right).
Moves the image vertically (up or down).
Increases or decreases the horizontal size of the image.
Increases or decreases the vertical size of the image.
Geometry Controls
The Geometry controls allow you to adjust the curvature or angle of the
sides of your display.
Increases or decreases the curvature of the sides either inward or outward.
Increases or decreases the curvature of the sides either to the left or right.
Increases or decreases the tilt of the sides either to the left or right.
Increases or decreases the top of the screen to be the same as the bottom.
Color Control/AccuColor® Control System
Two color presets select the desired color setting. Each color setting is
adjusted at the factory to the stated degree Kelvin.
R, G, B: NEC’s AccuColor Control System increases or decreases the
monitor’s red, green or blue color guns depending upon which is
selected. The change in color guns will appear on screen and the direction
(increase or decrease) will be shown by the bars.
4
78131861
6
5/21/98, 2:23 PM
Controls
Tools
Degauss Control: Eliminates the buildup of stray magnetic fields that
alter the correct scan of the electron beams and affect the purity of the
screen colors, focus and convergence. When activated, your screen
image will jump and waver a bit as the screen is demagnetized.
Caution: Please allow a minimum of 20 minutes to elapse
between uses of the Degauss Control.
Indicates the frequency setting of the monitor.
IPM™ System:
On: The IPM System works normally and all stages
of energy savings are utilized.
Off: The Off Mode of the IPM System is not used.
NOTE: For standard systems and graphics boards, keep the
factory setting at ON.
Selecting ALL RESET allows you to reset all OSM™ control settings back to
the factory settings except IPM System. Individual settings can be reset
by highlighting the control to be reset and pressing the RESET button.
5
78131861
7
5/21/98, 2:23 PM
Recommended Use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC® E SERIES COLOR MONITOR:
• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside
and opening or removing covers may expose you to dangerous shock hazards
or other risks. Refer all servicing to qualified service personnel.
• Allow adequate ventilation around the monitor so that heat can properly
dissipate. Do not block ventilated openings or place the monitor near a
radiator or other heat sources. Do not put anything on top of monitor.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch
dangerous voltage points, which can be harmful or fatal or may cause electric
shock, fire or equipment failure.
• Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.
• Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.
• Keep the monitor away from high capacity transformers, electric motors and
other devices such as external speakers or fans, which may create strong
magnetic fields.
• If possible, position the monitor so that it is facing the east to minimize the
effects of the earth’s magnetic field.
• Changing the direction of the monitor while it is powered on may cause image
discoloration. To correct this, turn the monitor off for 20 minutes before
powering it back on.
• The power cable connector is the primary means of detaching the system from
the power supply. The monitor should be installed close to a power outlet
which is easily accessible.
• Handle with care when transporting. Save packaging for transporting.
Immediately unplug your monitor from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following operating
instructions.
6
78131861
8
5/21/98, 2:23 PM
Recommended Use
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR
CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:
• Adjust the monitor height so that the top of the screen is at or slightly below
eye level. Your eyes should look slightly downward when viewing the middle
of the screen.
• Position your monitor no closer than 12 inches and no further away than 28 inches
from your eyes. The optimal distance is 18 inches.
• Rest your eyes periodically by focusing on an object at least 20 feet away.
Blink often.
• Position the monitor at a 90° angle to windows and other light sources to
minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do
not reflect on your screen.
• If reflected light makes it hard for you to see your screen, use an anti-glare filter.
• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a
non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to
minimize dust.
• Adjust the monitor’s brightness and contrast controls to enhance readability.
• Use a document holder placed close to the screen.
• Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your head
while you are typing.
• Get regular eye checkups.
For more detailed information on setting up a healthy work environment, call NEC
at (800) 820-1230, NEC FastFacts™ information at (800) 366-0476 and request
document #900108 or write the American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard
No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa Monica,
California 90406.
7
78131861
9
5/21/98, 2:23 PM
Specifications
Monitor
MultiSync® E500™
Notes
Specifications
Picture Tube
Monitor
15 inch
Diagonal:
90° deflection, 0.25 mm mask pitch,
CromaClear™ CRT, medium-short persistence
phosphor, multi-layered, anti-static screen
coating, dark-tint screen, Invar Shadow Mask
and OptiClear® screen surface.
Viewable Image Size:
Radius:
13.8 inch
1080 mm
Input Signal
Video:
Sync:
ANALOG 0.7 Vp-p/75 Ohms
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors
Analog input:
Unlimited number of Colors
Depends on display card used.
Synchronization
Range
Horizontal:
Vertical:
31 kHz to 69 kHz
55 Hz to 120 Hz
Automatically
Automatically
Resolutions Supported
640 x 480 @ 60 to 120 Hz
800 x 600 @ 55 to 108 Hz
832 x 624 @ 55 to 103 Hz
Some systems may not support
all modes listed.
Resolution based on horizontal and
vertical frequencies only
1024 x 768 @ 55 to 85 Hz ....................... NEC cites recommended resolution at
1152 x 870 @ 55 to 75 Hz
1280 x 1024 @ 55 to 65 Hz
75 Hz for optimal display performance.
Active Display Area
(Factory Setting)
Horizontal:
Vertical:
270 mm/10.6 inches
202 mm/8 inches
Dependent upon signal timing used,
and does not include border area.
Active Display Area
(Full Scan)
280 mm/11 inches
210 mm/8.3 inches
Dependent upon signal timing used,
and does not include border area.
Power Supply
Current Rating
Dimensions
AC 100 – 120 V, 50/60 Hz
1.8A @ 100
–
120 V
372 mm (W) x 402 mm (H) x 412 mm (D)
14.6 inches (W) x 15.8 inches (H) x 16.2 inches (D)
Weight
15.1 kg
33.2 lbs
Environmental Considerations
Operating Temperature:
Humidity:
10°C to +35°C
30% to 80%
Feet:
0 to 10,000 Feet
-20°C to +60°C
10% to 90%
Storage Temperature:
Humidity:
Feet:
0 to 45,000 Feet
NOTE: Technical specifications are subject to change without notice.
8
78131861
10
5/21/98, 2:23 PM
Monitor
MultiSync® E700™
Monitor
17 inch
15.6 inch
1210 mm
Notes
Specifications
Picture Tube
Diagonal:
90° deflection, 0.25 mm mask pitch,
CromaClear™ CRT, medium-short persistence
phosphor, multi-layered, anti-static screen
coating, dark-tint screen, Invar Shadow
Mask and OptiClear® screen surface.
Viewable Image Size:
Radius:
Input Signal
Video:
Sync:
ANALOG 0.7 Vp-p/75 Ohms
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors
Analog input:
Unlimited number of Colors
Depends on display card used.
Synchronization
Range
Horizontal:
Vertical:
31 kHz to 82 kHz
55 Hz to 120 Hz
Automatically
Automatically
Resolutions Supported
640 x 480 @ 60 to 120 Hz
800 x 600 @ 55 to 120 Hz
832 x 624 @ 55 to 120 Hz
Some systems may not support
all modes listed.
Resolution based on horizontal and
vertical frequencies only
1024 x 768 @ 55 to 100 Hz ..................... NEC cites recommended resolution at
1152 x 870 @ 55 to 89 Hz
1280 x 1024 @ 55 to 76 Hz
1600 x 1200 @ 55 to 65 Hz
85 Hz for optimal display performance.
Active Display Area
(Factory Setting)
Horizontal:
Vertical:
306 mm/12.0 inches
230 mm/9.1 inches
Dependent upon signal timing used,
and does not include border area.
Active Display Area
(Full Scan)
316 mm/12.4 inches
237 mm/9.3 inches
Dependent upon signal timing used,
and does not include border area.
Power Supply
Current Rating
Dimensions
AC 100 – 120 V, 50/60 Hz
1.8A @ 100
–
120 V
403 mm (W) x 426 mm (H) x 453 mm (D)
15.9 inches (W) x 16.8 inches (H) x 17.8 inches (D)
Weight
19.5 kg
43.0 lbs
Environmental Considerations
Operating Temperature:
Humidity:
10°C to +35°C
30% to 80%
Feet:
0 to 10,000 Feet
-20°C to +60°C
10% to 90%
Storage Temperature:
Humidity:
Feet:
0 to 45,000 Feet
NOTE: Technical specifications are subject to change without notice.
9
78131861
11
5/21/98, 2:23 PM
Features
CromaClear™ CRT: Delivers images with more clarity than found in traditional
CRT’s. Phosphors appear elliptical when illuminated, resulting in screen images
with more depth and dimension.
OptiClear® Screen Surface: Reduces reflection and glare and increases contrast
without sacrificing focus level, clarity or brightness. Along with the flat square
technology CRT, a high contrast screen with 0.25 mm mask pitch delivers crisp,
clean text and graphics.
Invar Shadow Mask: Holes in the thin metal sheet behind the glass of the CRT
surface correspond to each phosphor dot on the inner surface of the CRT’s
faceplate, allowing the correct electron beam (red, green, blue) to hit the correct
color phosphor for improved focus, brightness and color.
AccuColor® Control System: Allows you to adjust the colors on your screen and
customize the color accuracy of your monitor to a variety of standards.
OSM™ (On-Screen Manager) Controls: Allow you to quickly and easily adjust all
elements of your screen image via simple to use on-screen menus.
ErgoDesign® Features: Enhance human ergonomics to improve the working
environment, protect the health of the user and save money. Examples include
OSM controls for quick and easy image adjustments, tilt/swivel base for pre-
ferred angle of vision and compliance with MPRII guidelines for lower emissions.
Plug and Play: The Microsoft® solution with the Windows®95 operating system
facilitates setup and installation by allowing the monitor to send its capabilities
(such as screen size and resolutions supported) directly to your computer,
automatically optimizing display performance.
IPM™ (Intelligent Power Manager) System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption level when
on but not in use, saving two-thirds of your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace.
Reduced Magnetic Field™ Technology: Reduces magnetic and alternating electric
field emissions and static electricity, addressing ergonomic concerns regarding
potential risks from extended computer monitor use.
Multiple Frequency Technology: Automatically adjusts monitor to the display
card’s scanning frequency, thus displaying the resolution required.
FullScan™ Capability: Allows you to use the entire screen area in most resolu-
tions, significantly expanding image size.
OSM Display Screen Copyright 1997 by NEC Technologies, Inc.
10
78131861
12
5/21/98, 2:23 PM
Troubleshooting
No picture
• Display card should be completely seated in its slot.
• Power Button and computer power switch should be in the ON position.
• Signal cable should be completely connected to display card/computer.
• Check connector for bent or pushed-in pins.
Image is scrolling or unstable
• Signal cable should be completely attached to the computer.
• Check pin assignments and signal timings of the monitor and your
display card with respect to recommended timings and pin assignments.
• If the Macintosh cable adapter is used, check for prior connection or
make sure the display card is Macintosh compatible and that the card is
properly seated in the computer.
LED on monitor is not lit (no green, orange, yellow color can be seen)
• Power Switch should be in the ON position and power cord should
be connected.
Picture is fuzzy or color looks blotchy
• Adjust Brightness and Contrast Controls.
• Access the Degauss Control through OSM™ controls. Activate the
Degauss Control.
CAUTION: A minimum interval of 20 minutes should elapse before the
Deguass Control is used a second time when not switching
between modes.
Picture bounces or a wavy pattern is present
in the picture
• Move electrical devices that may be causing electrical interference away
from the monitor.
• See inside cover of User’s Manual for FCC information.
Edges of the display image are not square
• Use the OSM Geometry Controls to straighten the edges.
• If possible, position the front of the monitor facing east.
Display image is not centered, too small, or too large
• Use the OSM Size and Position Controls to adjust the image.
11
78131861
13
5/21/98, 2:23 PM
References
• BBS
(508) 635-4706
NEC Technologies’ Remote Bulletin Board System is an electronic service
accessible with your system and a modem. Communication parameters
are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits,
1 stop bit
• Customer Service/
Technical Support
Fax
(800) 632-4662
(508) 635-4298
• Direct Sales
(800) 374-8000
• Electronic Channels:
Internet ftp site: ftp.nectech.com
• FastFacts™ Information
INFORMATION
MultiSync® E500™ monitor
MultiSync® E700™ monitor
Glossary
(800) 366-0476
DESCRIPTION
DOCUMENT #
157501
Detailed monitor information
Detailed monitor information
174601
Definition of terms related
to functions, features and
installation of the
900203
MultiSync monitor
More Information
Names and addresses of
other groups involved in
standards and features of
the MultiSync monitor
900204
Macintosh Connection
Detailed information on
connecting the MultiSync
monitor to a Macintosh
153006
900108
Healthy Work Environment
Detailed information on
setting up a healthy work
environment
• Literature & Sales Info
• MultiSync Fulfillment
(800) NEC-INFO [(800) 632-4636]
(800) 820-1230
[For software & accessories]
• TeleSales
(800) 284-4484
12
78131861
14
5/21/98, 2:23 PM
Limited Warranty
NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from
defects in material and workmanship and, subject to the conditions set forth below, agrees
to repair or replace any part of the enclosed unit which proves defective for a period of three
(3) years from the date of first consumer purchase. Spare parts are warranted for ninety
(90) days.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. This warranty is limited to the original purchaser of the Product and is not
transferable. This warranty covers only NECTECH-supplied components. Service required as
a result of third party components is not covered under this warranty.
Proof of Purchase will be required by NECTECH to substantiate date of purchase. Such proof
of purchase must be an original bill of sale or receipt containing name and address of seller,
purchaser, and the serial number of the product.
It shall be your obligation and expense to have the Product shipped, freight prepaid, or
delivered to the authorized reseller from whom it was purchased or other facility authorized
by NECTECH to render the services provided hereunder in either the original package or a
similar package affording an equal degree of protection. All Products returned to NECTECH
for service MUST have prior approval, which may be obtained by calling 1-800-632-4662.
The Product shall not have been previously altered, repaired, or serviced by anyone other
than a service facility authorized by NECTECH to render such service, the serial number
of the product shall not have been altered or removed. The Product shall not have been
subjected to accident, misuse, or abuse or operated contrary to the instructions contained
in the User’s Manual.
NECTECH SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,
OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH
PRODUCTOTHERTHANTHELIABILITYSTATEDABOVE. THESEWARRANTIESAREINLIEUOF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
This Product is warranted in accordance with the terms of this limited warranty. Consumers
are cautioned that Product performance is affected by system configuration, software, the
application, customer data, and operator control of the system, among other factors. While
NECTECH Products are considered to be compatible with many systems, specific functional
implementation by the customers of the Product may vary. Therefore, suitability of a Product
for a specific purpose or application must be determined by consumer and is not warranted
by NECTECH.
For the name of your nearest authorized NECTECH service facility, contact NECTECH
at 1-800-632-4662.
13
78131861
15
5/21/98, 2:23 PM
NEC Enterprise Series
PROPRIETARY NOTICE AND LIABILITY DISCLAIMER
The information disclosed in this document, including all designs and related materials, is the valuable property of NEC
Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this
document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights
are expressly granted to others.
The NEC Technologies product(s) discussed in this document are warranted in accordance with the terms of the Limited
WarrantyStatementaccompanyingeachproduct.However,actualperformanceofeachsuchproductisdependentupon
factors such as system configuration, customer data and operator control. Since implementation by customers of each
product may vary, the suitability of specific product configurations and applications must be determined by the customer
and is not warranted by NEC Technologies.
To allow for design and specification improvements, the information in this document is subject to change at any time
without notice. Reproduction of this document or portions thereof without prior approval of NEC Technologies is
prohibited.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
U.S. Responsible Party: NEC Technologies, Inc.
Address:
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143
Tel. No.:
(630) 775-7900
Type of Product:
Equipment Classification:
Models:
Computer Monitor
Class B Peripheral
JC-1575VMA and JC-1746UMA
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
MultiSyncisaregisteredtrademarkofNECTechnologies, Inc. intheU.S. andofNECHomeElectronics, Ltd. inCanada, UK, Germany, France,
Spain, Italy, Austria, Benelux, Switzerland, Denmark, Finland, Norway and Saudi Arabia. AccuColor, OptiClear and ErgoDesign are
registered trademarks of NEC Technologies, Inc. in the U.S. and Canada. E500, E700, Reduced Magnetic Field, IPM, FastFacts, FullScan and
OSM are trademarks of NEC Technologies, Inc. in the U.S. NEC is a registered trademark of NEC Corporation Copyright 1997 by NEC
Technologies, Inc. OSM Display Screens Copyright 1997 by NEC Technologies, Inc. Windows is a registered trademark of Microsoft
Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners.
The Energy Star emblem does not represent EPA endorsement of any product or service.
Part No. 78131861
Printed in Malaysia
78131861
16
5/21/98, 2:23 PM
|