Jasco Universal Remote RM24993 User Manual

RM24993  
Universal Remote  
Instruction Manual  
CBL  
VCR  
AUX  
DVD  
SAT  
TV  
INPUT  
ENTER  
 
Setup  
Battery Installation  
1. On the back of the remote, push down on the  
tab and lift the cover off.  
2. Match the batteries to the + and - marks inside  
the battery case, then insert 2 AAA Alkaline  
batteries.  
3. Press the battery cover back into place.  
Battery Saver  
Your remote automatically turns off if the buttons  
are depressed more than 30 seconds. This will  
save your batteries should your remote get stuck in  
a place where the buttons remain depressed (e.g.,  
between the sofa cushions).  
Code Saver  
You will have up to 10 minutes to change the  
batteries in your remote without losing codes you  
have programmed. However, do not press any  
buttons until batteries are installed in the remote.  
If buttons are pressed without batteries in the  
remote, all codes will be lost.  
Code Setup  
The SETUP button is used to setup the remote.  
You can either setup the remote using the code  
for your brand of product, from the code tables (on  
separate sheet), or you can search through the  
library of codes until you find a code that works  
for your product. Please refer to “Programming  
with Code Search” page 9 for more information  
on using the code search feature to learn how  
to search through the library of codes for your  
products. NOTE: You can store any kind of code  
under any mode (except TV). I.E. you can store  
a VCR code under the CABLE button, or a DVD  
code under the VCR button, etc. However, you can  
only store TV codes under the TV button.  
3
 
Button Functions  
Some buttons on the remote might have functions that  
are referred to by different names on the device you  
are controlling. E.G. LAST may be called RECALL,  
or ENTER may be called DISPLAY. These differences  
depend on the brand and model of your product. Also,  
this remote can only operate features that exist on your  
product. E.G., your product must have LAST ability for  
the LAST button to operate this feature.  
TV, DVD, etc. Selects prod-  
uct to be operated.  
VOLUME UP/DOWN  
Changes the volume  
level of the product,  
normally the TV.  
MUTE Turns off the  
TV sound while the  
picture remains.  
OK Selects menu  
items for the device  
you are controlling.  
PREV. CH Returns to  
the previously selected  
channel.  
SETUP For setup.  
SHIFT Accesses  
shifted functions.  
INPUT  
For some TVs, press  
repeatedly to select  
from available viewing  
sources (antenna, cable  
box, VCR, etc.).  
RECORD, PLAY, STOP,  
REW, FF, PAUSE VCR  
control buttons operate your  
VCR even when the remote  
is set to operate the TV.  
Also operates DVD Scan  
-/+. Note the VCR keys also  
control DVD when in DVD  
Mode.  
4
 
Button Functions, cont.  
Red Indicator  
CHANNEL Up/Down  
Lights when any  
button is pressed.  
Changes the channels.  
SLEEP enables  
the remote to turn  
off your TV after a  
period of 1 to 99  
minutes.  
EXIT Exit On-Screen  
Menus and/or Return  
to previous On-Screen  
selection.  
INFO button brings up  
DVD Display or Control  
Menu for Chapter/Track/  
Title number, Time re-  
maining/elapsed indica-  
tion, system information,  
etc.  
MENU  
Selects the on-screen  
menu.  
NUMBERS  
Enter numbers for direct  
channel selection. Some  
products require ENTER  
to be pressed after chan-  
nel selection.  
ENTER  
For some TV models,  
used after direct chan-  
nel number  
entry to immediately  
change to the  
ON-OFF Turns  
device On or Off.  
selected channel.  
Note: The REC button must be pressed TWICE to record  
from your VCR. For some brands of VCRs, you might  
need to press the REC button once, then press it again  
for three seconds.  
5
 
DVD Functions  
This remote controls many DVD functions. The  
descriptions may vary from your original remote  
descriptions.  
REW and FF buttons control the speed of Fast  
Forward and Reverse Playback respectively.  
CHAN+/CHAN- buttons respectively locate the  
succeeding or preceding Chapters or Tracks on a  
disc.  
INFO button brings up DVD Display or Control  
Menu for Chapter/Track/Title number, Time remain-  
ing/elapsed indication, system information, etc.  
MENU brings up the DVD disc Menu screen - use  
with the UP, DOWN, LEFT & RIGHT navigation  
buttons.  
OK button is used for on-screen Menu selection.  
Note some DVD players require the Play button to  
be used.  
EXIT Exit On-Screen Menus and/or Return to pre-  
vious On-Screen selection.  
PLAY button is used to start Disc playback and for  
Menu selection on some DVD players.  
STOP button stops Disc playback.  
PAUSE button pauses Disc playback - press PLAY  
to resume.  
INPUT brings up the DVD Players Setup Menu.  
Note, not all DVD Players support all the functions  
described above.  
SAT Functions  
CHAN+ and CHAN- buttons perform the “Page+”  
and “Page-” function for on-screen Guide Menus  
used by some Satellite systems.  
INFO button brings up Satellite Display screen for  
current Channel and system information.  
MENU brings up the Satellite Menu screen - use  
with the UP, DOWN, LEFT & RIGHT navigation  
buttons.  
OK button is used for on-screen Menu selection.  
EXIT button is used to Exit or Clear on-screen  
Menu displays.  
INPUT button performs the Satellite TV/SAT  
function.  
6
 
Direct Code Entry  
1. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
2. Press and release the desired mode  
button (TV, VCR, etc.). The red indicator  
blinks, then stays lit.  
3. Enter the 4 digit code  
from the code tables  
(on separate sheet).  
Note: after a valid  
code entry, the red  
indicator turns off. For  
an invalid code, the  
red indicator flashes.  
4. With your device on, press ON/  
OFF. If the device turns off, no  
further programming is required.  
Note: If some buttons do not  
operate your equipment, try one of  
the other codes for your brand.  
Write your codes down here for easy reference  
later.  
Device  
Device stored Code  
TV  
TV  
DVD  
CBL/SAT  
VCR/AUX  
7
 
Code Search  
If your device does not respond after you have  
tried all the codes for your brand, or if your brand is  
not listed, try searching for your code by following  
these steps.  
1. Manually turn on the device (TV, VCR, etc.) to  
be controlled.  
2. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
3. Press and quickly release the desired  
mode button (TV, VCR, etc.). The red  
indicator blinks off once.  
4. Press the CHANNEL UP button  
repeatedly (up to 300 times)  
until the device to be controlled  
changes channel. The red  
indicator blinks off with each  
button press. If you accidentally overshoot the  
code required, press the CHANNEL DOWN  
button to backtrack through the library until the  
device changes channel. Pressing CHANNEL  
UP changes direction to forward again.  
5. Press and release ENTER to install the  
code.  
Most users will store VCR codes under the VCR button,  
Cable codes under CABLE, etc. If (for example) you  
want to store a VCR code under CABLE, first follow  
the procedure for Direct Code Entry (page 8) and press  
CABLE in step 2 of Direct Code Entry, then enter ANY  
VCR code in step 3 of Direct Code Entry. Then follow the  
steps above for Code Search.  
Note: If the device does not have a CHANNEL UP  
button, use PLAY (VCR only) or POWER instead.  
Code Search starts from the currently stored three digit  
number under that mode. Sometimes the first code  
that “works” with your device may only allow limited  
functionality (e.g. the MENU button might not work).  
There may be a code that performs more functions.  
Continue the code search process until the best code is  
found.  
8
 
Code Identification  
The Code Identification Feature allows you to  
identify the 4 digit library code stored under your  
device key. For example, if you want to find out  
what 4 digit code is stored under your TV device  
key, follow the six steps below:  
1. Press and hold the SETUP button until  
the red indicator stays on. Release the  
SETUP button.  
2. Press and release the desired mode  
button (TV, VCR, etc.). The red  
indicator blinks, then stays lit.  
3. Press and release the SETUP button.  
The red indicator blinks once and  
remains lit.  
4. To nd the first digit for  
the code stored under the  
mode key pressed in step  
2, press each numeric  
key from 0-9 in turn. The  
number that causes the  
indicator light to blink is  
the first digit in your code.  
5. To nd the second digit, repeat step 4.  
6. Repeat step 4 again to find the third and fourth  
digits. This time the red indicator turns off and  
stays off.  
9
 
Using Your Remote  
SHIFT  
Press SHIFT (Setup) prior to the shifted key func-  
tion e.g., for,  
MENU - press and release SHIFT (Setup) then  
MENU (Info).  
UP - press and release SHIFT then UP (Chan+).  
DOWN - press and release SHIFT then DOWN  
(Chan-).  
LEFT - press and release SHIFT then LEFT (Vol-).  
RIGHT - press and release SHIFT then RIGHT  
(Vol+).  
OK - press and release SHIFT then OK (Mute).  
EXIT - press and release SHIFT then EXIT  
(Sleep).  
The red indicator blinks for each keypress.  
Controlling Devices with Separate  
Power On and Off Buttons  
Some GE, RCA and ProScan models require  
you to press the device button for more than one  
second to turn the device on and the POWER  
button to turn the device off.  
Controlling Combo Devices  
Some Combo devices (e.g. TV/VCR, TV/DVD,  
DVD/VCR, etc.) will require you to set up two  
different Mode buttons to control both parts of the  
Combo device. For example, if you have a TV/  
DVD Combo, you might need to set up one code  
under the TV button to control the TV part AND a  
separate code (under any other Mode button) to  
control the DVD part.  
VCR/DVD Punch-Through  
This remote allows the 6 VCR transport buttons  
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and  
REC) to Punch-Through control from any Mode  
programmed with TV, SAT or Cable codes to the  
last VCR, or DVD programmed Mode you used.  
This feature will not operate if the programmed  
TV, SAT or Cable code has its own VCR transport  
button control e.g. a TV Combo, SAT/PVR, etc.  
10  
 
Using Your Remote, cont.  
Volume/Mute Control and Punch-  
Through  
This remote lets you select which device Mode  
controls your Volume/Mute buttons. The remote is  
initially set for all device Modes to use their own  
Volume/Mute control if present. If the programmed  
code has no Volume/Mute operation of its own  
then those buttons will punch-through control to  
the TV Mode device without needing to change to  
TV Mode.  
Setting ALL Volume/Mute Control to  
any one Mode  
This routine can set all Modes to “punch-through”  
to any one chosen Mode for Volume/Mute button  
control without the needing to change to that  
Mode.  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
the button.  
2. Press and hold the MUTE button until  
the red indicator blinks off, then release  
the button.  
3. Press and release the desired Mode button  
(TV, VCR, etc.) for Volume/Mute control,  
the red indicator blinks then stays on.  
4. Press and release the MUTE button  
and the red indicator turns off. The  
red indicator will blink rapidly for  
three seconds if the Mode you have  
selected has no Volume/Mute control.  
All other Modes will now punch-through to your  
chosen Mode for Volume/Mute control.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Using Your Remote, cont.  
Setting any Mode to use its own  
Volume/Mute Control  
This routine can set any Mode to use only its own  
Volume/Mute control. Note - If your chosen Mode  
has no Volume/Mute functions of its own then the  
Volume/Mute buttons will do nothing.  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
the button.  
2. Press and hold the MUTE button until  
the red indicator blinks off, then release  
the button.  
3. Press and release the desired Mode  
button (TV, VCR, etc.), the red indicator  
blinks then stays on.  
4. Press and release the VOLUME-  
(Down) button, the red indicator blinks  
then stays on.  
5. Press and release the MUTE button and  
the red indicator turns off.  
Your chosen Mode will now use its own Volume/  
Mute control.  
12  
 
Using Your Remote, cont.  
Sleep Function  
The Sleep button enables the remote to turn off  
your TV after a period of 1 to 99 minutes as shown  
below. The remote must be in TV mode to set a  
Sleep Timer. This feature works even if your TV  
does not have a sleep feature.  
1. Press and release the TV device button.  
2. Press and hold the Sleep button until  
the LED remains lit (about 2-3 sec-  
onds).  
3. Release the Sleep button.  
4. Press and release the  
numeric buttons (01-99)  
for the time required.  
The LED will blink off to  
indicate button press  
acceptance.  
5. TV Sleep Timer is set.  
6. Leave the Remote pointing towards the TV  
with an unobstructed path.  
To cancel the Sleep Timer, press and hold the  
Sleep button until the LED blinks, or press and  
release the Power button in TV mode.  
13  
 
Troubleshooting  
Remote does not operate your product.  
Press the mode button of the product you want  
to control.  
Program the remote with a new code.  
Install new batteries. (You might have to  
reprogram your remote after installing new  
batteries.)  
Remote may not be compatible with your  
product.  
Remote does not operate some  
features of your product.  
Sometimes a particular code might operate  
some features but not all. Try programing  
remote with a new code.  
Remote may not be able to operate all features  
of your product or button names might be  
different than your product.  
Red Indicator blinks after you program  
a product code.  
Remote did not accept the code.  
Try to program the code again or try a different  
code.  
Lost Your Codes?  
Enclosed with this remote is a sticker on which  
you should write the codes for each device you  
programmed. Apply the sticker to the back of  
the remote or somewhere convenient for future  
reference.  
Also on the sticker is our website address which,  
should you lose your codes or programming  
instructions, you can find available on our website:  
14  
 
90 Day Limited Warranty  
Jasco Products Company warrants this product  
to be free from manufacturing defects for a period  
of ninety days from the original date of consumer  
purchase. This warranty is limited to the repair  
or replacement of this product only and does not  
extend to consequential or incidental damage to  
other products that may be used with this unit.  
This warranty is in lieu of all other warranties  
express or implied. Some states do not allow  
limitations on how long an implied warranty lasts  
or permit the exclusion or limitation of incidental or  
consequential damages, so the above limitations  
may not apply to you. This warranty gives you  
specific rights, and you may also have other rights  
which vary from state to state. If unit should prove  
defective within the warranty period, return prepaid  
with dated proof of purchase to:  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114  
15  
 
RM24993  
Universal Remote  
Instruction Manual  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114  
Made in China  
RM24993-2/07  
 

Indesit Oven FE 10 K GB User Manual
Indesit Washer SIXL 145K User Manual
Jabra Video Game Headset PR9460 User Manual
Jenn Air Range Dual Fuel Cooktop User Manual
JVC CD Player GET0172 001A User Manual
JVC TV VCR Combo TV 20240 User Manual
Kenmore Vacuum Cleaner 11634924 User Manual
Kenwood Microcassette Recorder TS 8305 User Manual
King Canada Sander KC 1632DS User Manual
Klipsch Speaker RB 51 User Manual