Jasco Headphones 86708 User Manual

a USB port on your computer and plug the other connector  
end into the bottom of the headset or into the desktop  
charging cradle. LED indications are the same as above.  
TO ANSWER AN INCOMING CALL  
To answer an incoming call, press TALK once.  
A couple low tone beeps (repeated until call is answered) will  
signify an attempt to connect is being made. A short higher  
tone beep will signify the connection was successfully made.  
To reject an incoming call, press and hold the TALK button for  
about two seconds.  
TURNING ON AND OFF THE HEADSET  
Bluetooth® Headset  
To turn on the headset, slide the switch to the ON position.  
A tone will signify the headset is being turned on. The LED  
indicator will flash green. To turn off, slide the switch to OFF  
position. The LED indicator will also turn off.  
GE Model 86708  
CALL WAITING  
User Guide  
The Call Waiting function on your phone would need to be  
turned on before this function could be used. Not all phones  
support Call Waiting. To accept a second incoming call and  
disconnect the first party, press TALK once when you hear the  
beep indicating an incoming call. To accept the second caller  
but place on hold the first party, press and hold the  
TALK button.  
BATTERY LOW INDICATION  
The LED indicator will flash red every 2.5 seconds when the  
battery becomes low in charge. Re-charging is recommended  
at this time.  
PAIRING YOUR HEADSET  
In order for your headset to communicate with your  
Bluetooth enabled phone the two must be “paired” together.  
You should consult your phone’s user manual on how to make  
such a pairing as all phones are slightly different.  
TRANSFER CALL BACK TO PHONE  
To transfer the call back to your phone, press TALK twice.  
CUSTOMER SERVICE INFORMATION  
Your headset needs to be “discoverable” by the phone (or  
other Bluetooth device) so the two can be linked together.  
To put the headset in the discoverable mode, push the TALK  
button and hold it (for about five seconds) until the LED  
indicator begins flashing green and red alternately and you  
will also hear a beep tone in the earpiece. Then select the  
function on your phone which makes the phone search or  
“look for” Bluetooth devices. This linking procedure should be  
explained in your phone’s user manual.  
In addition to the troubleshooting table on this page you can  
email help at: [email protected] or call 800 654-  
8483. For other Bluetooth products or support, please view  
LED  
Indicator  
Light  
Volume  
Controls  
On/Off  
Switch  
90-Day Limited Warranty  
Desktop  
Charger  
Jasco Products Company warrants this product to be free  
from manufacturing defects for a period of ninety days  
from the original date of consumer purchase. This warranty  
is limited to the repair or replacement of the product only  
and does not extend to consequential or incidental damage  
to other products that may be used with this unit. This  
warranty is in lieu of all other warranties express or implied.  
Some states do not allow limitations on how long an implied  
warranty lasts or permit the exclusion or limitation of  
incidental or consequential damages, so the above limitations  
may not apply to you. This warranty gives you specific rights,  
and you may also have other rights which vary from state  
to state. If unit should prove defective within the warranty  
period, return prepaid with dated proof of purchase to:  
Jasco Products Company, 311 N.W. 122nd St.,  
Microphone  
Earbud  
Once it has “found” or linked with the headset then it is  
ready to be paired. Your mobile phone will prompt you for  
a password, PIN, or pairing code (wording varies by phone  
manufacturer). At that point ENTER 0000. You will then  
most likely be prompted by the phone whether you want to  
connect with the headset. After you respond affirmatively you  
should then get confirmation that your phone and headset  
are “connected”. The GE 86708 headset is now in standby  
mode and ready for use. The LED indicator will flash green  
more rapidly once connected.  
Talk Button  
AC Adapter  
Charger  
USB Cable  
GE 86708 COMPONENTS  
• Headset  
• Desktop Charger Module  
• AC Adapter/Charger  
• USB Cable for PC Charging  
• Two Rechargeable  
NiMH batteries  
Pairing Notes:  
• This headset can be paired with up to eight phones/devices.  
The most recently paired phone will be at the top of the list.  
• When the TALK button is pressed in standby mode the  
headset will try to connect to the most recently paired  
phone only.  
• The GE 86708 can also be paired with other Bluetooth  
enabled devices like computers or voice access gateway  
type products.  
Oklahoma City, OK 73114  
INSERTING BATTERIES  
To insert the batteries, open the battery door on the  
FCC Information  
underside of the headset. Pull back the small tab (toward the  
black dot) and at the same time use fingernail on other hand  
to open battery door. The top end of the battery door (near  
tab) should open. The bottom end of the door is hinged so do  
not force it. Insert batteries with positive end of both batteries  
pointed up toward tab. Replace door, by again sliding tab up  
to allow door to fall back into original position.  
This device complies with Part 15 of the FCC Rules. Operation  
is subject to the following two conditions: (1) this device  
may not cause harmful interference, and (2) this device may  
accept any interference received, including interference that  
may cause undesired operation.  
Privacy of communications may not be ensured when using  
this device.  
TO MAKE CALLS  
You can make calls by either a) dialing directly from your  
phone, b) using Voice Dialing, or c) using Last Number Redial  
function. To use Voice Dialing or Last Number Redial these  
must be supported by your mobile phone. Consult your  
phone’s user manual for phone-specific instructions.  
CHARGING YOUR HEADSET  
Warning: Changes or modifications to this equipment not  
expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment.  
Before using your headset you must charge the batteries. We  
recommend that for the very first charging the headset be  
allowed to charge for six (6) hours. Subsequent charging will  
take 1-2 hours. The headset can be charged in either the ON  
or the OFF position.  
NOTE: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and  
can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on. The user is  
encouraged to try to correct the interference by one or more  
of the following measures:  
Before using the Voice Dial function you must first set up  
“voice tags” according to your phone’s user’s manual. To  
make a Voice Dial call simply press the TALK button once to  
enable Voice Dialing. You will hear a couple low tone beeps  
to signify an attempt to connect. To call using Last Number  
Redial press twice the TALK button.  
Desktop Cradle Charging: Plug in one end of AC adapter into  
AC wall outlet and plug the connector end into the desktop  
cradle. Insert the headset into the desktop charging cradle  
making sure the metal contacts on the end of the headset  
touch the contacts in the cradle. The LED indicator by the  
ON-OFF switch will show continuous red which indicates the  
headset is charging. When fully charged the LED indicator will  
change to a continuous green color.  
NOTE: Thisheadsetwillworkwithin33-feetor10-metersfrom  
thelocationofthephoneorotherBluetoothenableddevice.  
TO END CALLS  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and  
the receiver.  
• Connect the equipment into an outlet o a circuit different  
from that to which the receiver is needed.  
To end a call, press the TALK button once after conversation  
has ended. A double tone will sound.  
Charging With AC Adapter: Plug AC adapter into the AC wall  
outlet and plug the connector end into the bottom end of the  
headset (on the side with the ON-OFF switch). LED indications  
are same as above.  
VOLUME CONTROL  
Press the VOLUME + to increase volume and VOLUME – to  
decrease volume. A short beep will be heard indicating that  
maximum or minimum volume level is reached.  
Charging With the USB Cable: You can charge your headset  
by using the power from you desktop or laptop computer.  
Using the supplied USB cable plug the USB connector end into  
• Consult the dealer or an experienced radio/TV  
technician for help.  
86708-1 vers. 1 7/06  
 

Insignia Car Speaker NS PSD5321 User Manual
Invacare Mobility Aid AX3 User Manual
Invacare Wheelchair Excelerator User Manual
Jabra Conference Phone HFS100 User Manual
Jenn Air Oven JJW8630DDB User Manual
Jensen MP3 Docking Station JiMS 198i User Manual
JVC Camcorder LYT2259 002C M User Manual
JVC Car Video System GD 463D10E User Manual
KitchenAid CD Player KEMI371B User Manual
KitchenAid Oven KEBC147KBL07 User Manual