USER GUIDE
Universal
Vehicle Mount
NS-MVMU5/ NS-MVMU5-C
Before using your new product, please read these instructions to prevent any damage.
UNIVERSAL VEHICLE MOUNT
Car Window Mount
PACKAGE CONTENTS
•
•
•
•
Car Air Vent Mount
Car Window Mount
Holder
360°
swivel
head
Flexible arm
User Guide
Adjustment knob
FEATURES
Suction lever
Your Insignia car mount securely holds
a smartphone to your car air vent or car
window. Make sure that your smartphone
is securely fastened to the mount before
you begin your trip.
Release button
Suction
cup
Holder Front
Caution: This mount is not intended for
extreme off-road use. Excessive bumping
and jarring may result in damage to your
device.
Clamps
Car Air Vent Mount
Spring-loaded clips Clip stops
Release
button
Hooks
Feet
360°
swivel
head
Holder Back
Kickstand
Adjustment knob
Swivel
head slot
feet
3
UNIVERSAL VEHICLE MOUNT
2
Align the clip stops with the edge of an
air vent louver, slowly push the mount
back until it clicks into place, then
release the mount. Make sure both
hooks are attached to the louver.
PLACING A SMARTPHONE IN
THE HOLDER
1 Repeatedly press the release button on
the side of the holder. The clamps open.
2 Unfold the feet on the bottom of the
holder.
3 Adjust the clamps to fit the width of
your smartphone.
4 Place your smartphone in the holder
and close the clamps by squeezing
them together tightly until your phone
is secure.
ATTACHING TO AIR VENT
LOUVERS
3
4
Position the kickstand so it rests against
other louvers or the dash for support.
Loosen the swivel head knob, adjust
the viewing angle, then fully tighten
the knob.
1
Insert the swivel head into the slot on
the back of the holder and slide it into
place until it is secure.
Caution: Do not adjust your Insignia
car mount while driving.
4
UNIVERSAL VEHICLE MOUNT
7
To remove the mount, press the
release button, then pull the suction
cup tab.
Caution: Do not adjust your Insignia
car mount while driving.
ATTACHING TO A CAR
WINDOW
1
2
Clean the window with a clean cloth.
Insert the swivel head into the slot
on the back of holder and slide it into
place until it is secure.
REMOVING YOUR
SMARTPHONE FROM THE
HOLDER
1
Hold your smartphone and repeatedly
press the release button on the
bottom of the holder. The clamps
open.
2
Remove your smartphone.
3
4
Remove the clear film from the suction
cup.
Push the release button on the
car window mount, press the suction
cup to the desired location on the
clean window, then press the lever
down.
The mount adheres to the window.
5
6
Loosen the adjustment knob, adjust
the viewing angle, then fully tighten
the knob.
Caution: Always loosen the
adjustment knob before changing the
viewing angle.
Bend the flexible arm to further adjust
the viewing angle.
5
UNIVERSAL VEHICLE MOUNT
ONE-YEAR LIMITED WARRANTY
CONTACT INSIGNIA
For customer service, call 877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
6
(877) 467-4289
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfi eld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V2 ENGLISH 14-0363
|